Franc Automation and Drives

We are authorized channel partner for ABB automation products.

MICRO DRIVES ACS150

  • Power range 0.37 to 4 kW/0.5 to 5 Hp
  • PID control, fixed keypad and speed control potentiometer
  • IP20 enclosure
  • Scalar control
  • Built-in brake chopper and Built-in EMC filter for 2 nd environment

MACHINERY DRIVES, ACS180

  • 4 to 18.5kW.
  • Wide operating voltage : Three Phase 380VAC, 323 to 456VAC.
  • Onboard MODBUS & optional CANlink.
  • Open loop V/F & SVC control; Staring torque of 150% at 0.5Hz(SVC) and 100% at 1Hz(V/F) ; Automatic torque boost.
  • Simplified parameter for easy start up
  • 4-Independent S-Ramps
  • Output frequency 500Hz
  • Overload : 150% for 60 Sec & 180% for 3 Sec
  • In-Built Dynamic braking unit

MICRO MACHINERY DRIVES, ACS355

  • 0.25kW to 22kW.
  • Quick commissioning – application macros and panel assistants.
  • Safe torque off function (SIL3) as standard.
  • Sensorless vector control for induction motors and permanent magnet motors up to 599 Hz.
  • Built-in braking chopper.
  • IP66 and solar pump drive variant available

MICRO MACHINERY DRIVES, ACS380

  • 0.25kW to 22kW.
  • Part of all-compatible drives portfolio.
  • Built-in EMC filters.
  • IP20 enclosure and coated circuit boards.
  • Unique 3-phase measurement – reliable earth fault protection.
  • Galvanically isolated fieldbus gives good noise immunity.
  • Ambient temperature of up to 50°C without derating.
  • Foil coated control panel – protection against dust and gases.
  •  Adaptive programming – sequential or block programming.
  • High starting torque, accurate speed control, stable torque or tolerance for suddenload variations with or without encoder feedback.
  • Simple positioning applications when using external motion controller.
  • supports perfectly both induction and permanent magnet motors.
  • Silent motor operation with energy optimizer.
  • Fast stop functions and parabolic speed reference
  • Load profile log, which shows you how the drive has been used.

GENERAL PURPOSE DRIVES, ACS560

  • Ultra-fast 4.5 kHz current loop.
  • Safe Torque Off – SIL3.
  • High speed EtherCAT communications – 125 μs.
  • 23 bit High resolution feedback encoder.
  • Short output winding Standard, built-in, short output winding ensures safe braking if the drive is unexpectedly disabled – even in the case of a failure in the motor holding brake.
  • Comprehensive data storage in case of failure.

GENERAL PURPOSE DRIVES, ACS580

  • 0.75kW to 500kW.
  • Part of all-compatible drives portfolio.
  • IP21, IP55, IP55 with switch and fuse.
  • Built-in features such as EMC C2 filter, choke, Modbus RTU fieldbus interface and safe torque off functionality.
  • The ATEX-certified thermistor protection module option CPTC-02.
  • IE2 drive (EN 50598-2) energy efficiency class, further reducing environmental impact.
  • ACS580 are compatible with high-efficiency IE4.
  • Side-by-side mounting, flange mounting and horizontal mounting are all available for wall-mounted ACS580 drives

INDUSTRIAL DRIVES, ACS880

  • ACS880 drives are designed for customers who value high quality and robustness in their applications. coated boards and high enclosure classes, making the ACS880 suitable for harsh conditions.
  • Additionally, every ACS880 drive is factory-tested at full load to ensure maximum reliability.
  • The tests include performance and all protective functions.
  • Nine-year maintenance interval.
  •  ABB’s signature DIRECT TORQUE CONTROL (DTC), which provides precise speed and torque control for all applications and supports virtually any type of motor.
  • Global product approvals, e.g. CE, UL, cUL, CSA, marine certifications, ATEX, marine
  • Regenerative drives, ultra-low harmonics drives, liquid cooled drives,
  • Speed, torque and position control as well as synchronizing
  • Ready-made optimized solutions for various applications and industries
  •  Special application softwares for EOT cranes, tower cranes, winches, artificial oil lifting, tunnel ventilation, position control, textile, test bench, centrifuge, decanter,

GENERAL PLC PLC H3U

  • All-in-one CPU, power supply and I/O.
  • Basic instruction: 100ns/instruction.
  • Program capacity: 64K steps.
  • Device memory
    • Auxiliary Relays 9216 points
    • Timers 512 points
    • Counters 256 points
    • Data Registers 9552 points
    • File Registers 32768 points
  • High-speed inputs: 200kHz
  • High-speed outputs: 200kHz(Standard Model) 500kHz(Motion Control Model).
  • Interpolation: two-axis arc and straight line, three-axis straight line(Motion Control Model), spiral line(Motion Control Model)
  • Three-axis electronic cam(Motion Control Model).
  • Supports MODBUS-RTU & MODBUS-TCP & CANlink/CANopen modes.
  • Maximum of 192 digital I/O(local).
  • Programming language: Ladder, Instruction list, SFC

GENERAL PURPOSE MICRO DRIVE MD 310

  • 4 to 18.5kW.
  • Wide operating voltage : Three Phase 380VAC, 323 to 456VAC.
  • Onboard MODBUS & optional CANlink.
  • Open loop V/F & SVC control; Staring torque of 150% at 0.5Hz(SVC) and 100% at 1Hz(V/F) ; Automatic torque boost.
  • Simplified parameter for easy start up
  • 4-Independent S-Ramps
  • Output frequency 500Hz
  • Overload : 150% for 60 Sec & 180% for 3 Sec
  • In-Built Dynamic braking unit

HIGH PERFORMANCE UNIVERSAL DRIVE MD 520

  • 3 Ph 380-480 Vac: 0.4 to 500 kW.
  • 3 Ph 200-240 Vac: 0.4 to 90 kW.
  • 1 Ph 200-240 Vac: 0.4 to 2.2 kW.
  • Operation in high ambient temperatures – up to 50degC.
  • Built-in DC reactor (400 V: 18.5 kW and above; 200 V: 11 kW and above.
  • Conformal coated PCBs compliant to 3S2 and 3C3 environments.
  • Complies to efficiency level IE2 as defined in IEC 61800-9-2.
  • Control modes: V/f for induction motor, Sensorless vector control (SVC), closed loop vector control (FVC) for both induction (asynchronous) and PMS motors.
  • Starting torque; 150% at 0.25 Hz for SVC; 180% at 0 Hz for FVC.
  • Communication options: Modbus-RTU, PROFIBUS-DP, CANopen, CANlink, PROFINET, EtherCAT, Ethernet/IP.
  • Brake control logic; inbuilt brake resistor upto 90kW.
  • Application dedicated functions: Centre winder, Textile wobble control, Master slave function. 4 motor parameter sets.
  • Bipolar analog input as standard (-10 to +10 V); PTC input as standard.
  • Output frequency: 599 Hz.
  • Encoder feedback (option): Incremental (HTL, Line Driver), Resolver, Serial encoder.

SINGLE AXIS SERVO SV660P-PULSE TYPE,SV660P-ETHERCAT

  • Ultra-fast 4.5 kHz current loop.
  • Safe Torque Off – SIL3.
  • High speed EtherCAT communications – 125 μs.
  • 23 bit High resolution feedback encoder.
  • Short output winding Standard, built-in, short output winding ensures safe braking if the drive is unexpectedly disabled – even in the case of a failure in the motor holding brake.
  • Comprehensive data storage in case of failure.

HIGH PERFORMANCE GENERAL PURPOSE DRIVE MD290

  • 4 to 500kW, Three Phase 380 to 480VAC.
  • Optional MODBUS-RTU, CANlink, Profibus-DP, CANopen.
  • Open loop V/F; Automatic torque boost.
  • 4-Independent S-Ramps
  • Output frequency 500Hz
  • Overload : 110% for normal duty and 150% for 60 Sec for heavy duty.
  • In-Built Dynamic braking unit upto 18.5kW
  • Built-in DC reactor EN61800-3 Category C2 2nd Environment.

HMI IT7000

  • 3 Ph 380-480 Vac: 0.4 to 500 kW.
  • 3 Ph 200-240 Vac: 0.4 to 90 kW.
  • 1 Ph 200-240 Vac: 0.4 to 2.2 kW.
  • Operation in high ambient temperatures – up to 50degC.
  • Built-in DC reactor (400 V: 18.5 kW and above; 200 V: 11 kW and above.
  • Conformal coated PCBs compliant to 3S2 and 3C3 environments.
  • Complies to efficiency level IE2 as defined in IEC 61800-9-2.
  • Control modes: V/f for induction motor, Sensorless vector control (SVC), closed loop vector control (FVC) for both induction (asynchronous) and PMS motors.
  • Starting torque; 150% at 0.25 Hz for SVC; 180% at 0 Hz for FVC.
  • Communication options: Modbus-RTU, PROFIBUS-DP, CANopen, CANlink, PROFINET, EtherCAT, Ethernet/IP.
  • Brake control logic; inbuilt brake resistor upto 90kW.
  • Application dedicated functions: Centre winder, Textile wobble control, Master slave function. 4 motor parameter sets.
  • Bipolar analog input as standard (-10 to +10 V); PTC input as standard.
  • Output frequency: 599 Hz.
  • Encoder feedback (option): Incremental (HTL, Line Driver), Resolver, Serial encoder.

PREMIUM INDUSTRIAL DRIVES ACS880

  • ACS880 drives are designed for customers who value high quality and robustness in their applications. coated boards and high enclosure classes, making the ACS880 suitable for harsh conditions.
  • Additionally, every ACS880 drive is factory-tested at full load to ensure maximum reliability.
  • The tests include performance and all protective functions.
  • Nine-year maintenance interval.
  •  ABB’s signature DIRECT TORQUE CONTROL (DTC), which provides precise speed and torque control for all applications and supports virtually any type of motor.
  • Global product approvals, e.g. CE, UL, cUL, CSA, marine certifications, ATEX, marine
  • Regenerative drives, ultra-low harmonics drives, liquid cooled drives,
  • Speed, torque and position control as well as synchronizing
  • Ready-made optimized solutions for various applications and industries
  •  Special application softwares for EOT cranes, tower cranes, winches, artificial oil lifting, tunnel ventilation, position control, textile, test bench, centrifuge, decanter,

PREMIUM GENERAL PURPOSE DRIVES ACS580

  • 0.75kW to 500kW.
  • Part of all-compatible drives portfolio.
  • IP21, IP55, IP55 with switch and fuse.
  • Built-in features such as EMC C2 filter, choke, Modbus RTU fieldbus interface and safe torque off functionality.
  • The ATEX-certified thermistor protection module option CPTC-02.
  • IE2 drive (EN 50598-2) energy efficiency class, further reducing environmental impact.
  • ACS580 are compatible with high-efficiency IE4.
  • Side-by-side mounting, flange mounting and horizontal mounting are all available for wall-mounted ACS580 drives

GENERAL PURPOSE DRIVES ACS560

ACS560 General Purpose Drive Product Image

  • Ultra-fast 4.5 kHz current loop.
  • Safe Torque Off – SIL3.
  • High speed EtherCAT communications – 125 μs.
  • 23 bit High resolution feedback encoder.
  • Short output winding Standard, built-in, short output winding ensures safe braking if the drive is unexpectedly disabled – even in the case of a failure in the motor holding brake.
  • Comprehensive data storage in case of failure.

MICRO MACHINERY DRIVES ACS380

ACS380 Machinery Drive
  • 0.25kW to 22kW.
  • Part of all-compatible drives portfolio.
  • Built-in EMC filters.
  • IP20 enclosure and coated circuit boards.
  • Unique 3-phase measurement – reliable earth fault protection.
  • Galvanically isolated fieldbus gives good noise immunity.
  • Ambient temperature of up to 50°C without derating.
  • Foil coated control panel – protection against dust and gases.
  • Adaptive programming – sequential or block programming.
  • High starting torque, accurate speed control, stable torque or tolerance for sudden load variations with or without encoder feedback.
  • Simple positioning applications when using external motion controller.
  • Supports perfectly both induction and permanent magnet motors.
  • Silent motor operation with energy optimizer.
  • Fast stop functions and parabolic speed reference
  • Load profile log, which shows you how the drive has been used.

MACHINERY DRIVES ACS180

ACS180 machinery drive
  • 4 to 18.5kW.
  • Wide operating voltage: Three Phase 380VAC, 323 to 456VAC.
  • Onboard MODBUS & optional CANlink.
  • Open loop V/F & SVC control; Starting torque of 150% at 0.5Hz (SVC) and 100% at 1Hz (V/F); Automatic torque boost.
  • Simplified parameter for easy startup
  • 4-Independent S-Ramps
  • Output frequency 500Hz
  • Overload: 150% for 60 Sec & 180% for 3 Sec
  • In-Built Dynamic braking unit

BASIC PLC H1U

  • All in one CPU and power supply supporting local and remote I/O.
  • 100 ns execution time per single, basic instruction.
  • Program capacity: 8 K steps.
  • Device memory
    • Auxiliary relays 3584 points
    • Timers 256 points
    • Counters 256 points
    • Data registers 8528 points
  • High speed inputs: up to 60 kHz.
  • High speed outputs: up to 100 kHz.
  • Supports RS485 (Modbus-RTU) and CANlink (Inovance proprietary) communication.
  • Maximum of 60 digital I/O (local), supports up to 30 remote modules (CANlink 3.0).
  • Programming language conforms to IEC 61131-3.
  • Ladder diagram (LD)/ Instruction list (IL)/ Sequential function chart (SFC).

GENERAL PURPOSE MICRO DRIVE ACS200

    • 0.4 to 2.2kW single phase; 0.75kW to 3.7kW three phase.
    • Wide operating voltage : Single Phase 170 to 264VAC; 3-phase 323V to 528V.
    • Internal EMC Filter; complies with EN61800-3 Category C2 2nd Environment  
    • Open loop V/F control; Staring torque of 150% at 3Hz; Automatic torque boost.
    • Modbus or CANLinkcomms 
    • Output frequency 500Hz 
    • Overload : 150% for 60 Sec & 180% for 3 Sec 
    • In-Built Dynamic braking unit 
    • Side-by-Side/ Wall Mounted/ DIN Rail Mounted

MICRO MACHINERY DRIVES ACS355

ACS355 Micro Drive Product Image

  • 0.25kW to 22kW.
  • Quick commissioning – application macros and panel assistants.
  • Safe torque off function (SIL3) as standard.
  • Sensorless vector control for induction motors and permanent magnet motors up to 599 Hz.
  • Built-in braking chopper.
  • IP66 and solar pump drive variant available.

MICRO DRIVES ACS150

ACS150 Micro Drive Product Image

  • Power range 0.37 to 4 kW/0.5 to 5 Hp
  • PID control, fixed keypad and speed control potentiometer
  • IP20 enclosure
  • Scalar control
  • Built-in brake chopper and Built-in EMC filter for 2nd environment